View G223_4578670.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MicroPower Direct
Compact MiniDIP, 2W Single & Dual Output DC/DC Converters
Key Features
Miniature DIP Package 2W Output Power 3.6 MH MTBF 1.0 kVDC Isolation Single & Dual Outputs Low Cost
G200 Series
Electrical Specifications
Specifications typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter Conditions Min. 5 VDC Input 4.5 12 VDC Input 10.8 24 VDC Input 21.6 48 VDC Input 43.2 Internal Capacitor Typ. 5.0 12.0 24.0 48.0 Max. 5.5 13.2 26.4 52.8 0.3 Typ. !1.0 Dual Output , Balanced Loads !0.1 For Vin Change of 1% !1.2 See Model Selection Guide 100 Over Line, Load & Temp. 120 !0.01 Momentary (0.5 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 50 Conditions Typ. !0.02 Conditions Min. Max. !3.0 !1.0 !1.5 150 200 5 Units
Input Voltage Range
VDC
Input Filter Reverse Polarity Input Current
A Units % % % mV P - P mV P - P mV rms % %/1C
Output
Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit
General
Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Max. Units VDC M pF kHz Units 1C 1C %
80 80
120 100 Max. +70 +125 95
Environmental
Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Min. Typ. -40 +25 -40 Free Air Convection RH, Non-condensing
Physical
Case Size, 5V, 12V & 24V Input Models Case Size, 48VDC Input Models Case Material Weight 0.80 x 0.40 x 0.27 Inches (20.32 x 10.16 x 6.85 mm) 0.80 x 0.40 x 0.30 Inches (20.32 x 10.16 x 7.50 mm) Non-Conductive Black Plastic 0.09 Oz (2.7g) Conditions MIL HDBK 217F, 251C, Gnd Benign Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input All Models
FAX: (781) 344-8481
Reliability Specifications
Parameter MTBF Min. Typ. 3.6 Typ. Max. Units MHours Units
Absolute Maximum Ratings
Parameter Min. -0.7 -0.7 -0.7 -0.7 Max. 9.0 18.0 30.0 55.0 650
Input Voltage Surge (1 Sec)
VDC
Internal Power Dissipation MicroPower Direct
TEL: (781) 344-8226
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. E-Mail: sales@micropowerdirect.com WEB: www/micropowerdirect.com
Model Selection Guide
Model Number G201 G202 G203 G204 G205 G206 G207 G211 G212 G213 G214 G215 G216 G217 G221 G222 G223 G224 G225 G226 G227 G231 G232 G233 G234 G235 G236 G237 Notes: Input Output Load Fuse Rating Efficiency Voltage (VDC) Current (mA) Slow-Blow Voltage Current Current Regulation (%, Typ) (%, Max) (mA) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) 5 4.5 - 5.5 452 35 3.3 500.0 10.0 11 73 1,000 5 4.5 - 5.5 526 35 5.0 400.0 8.0 11 76 1,000 5 4.5 - 5.5 495 35 12.0 165.0 3.0 7 80 1,000 5 4.5 - 5.5 499 35 15.0 133.0 2.5 7 80 1,000 5 4.5 - 5.5 519 35 10 77 1,000 !5.0 !200.0 !4.0 5 4.5 - 5.5 504 35 7 79 1,000 !12.0 !83.0 !1.5 5 4.5 - 5.5 501 35 7 79 1,000 !15.0 !66.0 !1.0 12 10.8 - 13.2 185 25 3.3 500.0 10.0 8 74 500 12 10.8 - 13.2 212 25 5.0 400.0 8.0 8 78 500 12 10.8 - 13.2 200 25 12.0 165.0 3.0 5 82 500 12 10.8 - 13.2 200 25 15.0 133.0 2.5 5 83 500 12 10.8 - 13.2 222 25 8 75 500 !5.0 !200.0 !4.0 12 10.8 - 13.2 201 25 5 82 500 !12.0 !83.0 !1.5 12 10.8 - 13.2 200 25 5 82 500 !15.0 !66.0 !1.0 24 21.6 - 26.4 92 10 3.3 500.0 10.0 8 74 200 24 21.6 - 26.4 108 10 5.0 400.0 8.0 8 77 200 24 21.6 - 26.4 101 10 12.0 165.0 3.0 5 81 200 24 21.6 - 26.4 101 10 15.0 133.0 2.5 5 82 200 24 21.6 - 26.4 111 10 8 75 200 !5.0 !200.0 !4.0 24 21.6 - 26.4 102 10 5 81 200 !12.0 !83.0 !1.5 24 21.6 - 26.4 100 10 5 82 200 !15.0 !66.0 !1.0 48 43.2 - 54.8 28 6 3.3 500.0 10.0 8 74 100 48 43.2 - 54.8 27 6 5.0 400.0 8.0 8 77 100 48 43.2 - 54.8 26 6 12.0 165.0 3.0 5 81 100 48 43.2 - 54.8 25 6 15.0 133.0 2.5 5 82 100 48 43.2 - 54.8 28 6 8 75 100 !5.0 !200.0 !4.0 48 43.2 - 54.8 26 6 5 81 100 !12.0 !83.0 !1.5 48 43.2 - 54.8 25 6 5 82 100 !15.0 !66.0 !1.0
Output Power %
"T"
1. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 2. These units do not require external comonents to operate, but the use of an input capacitor (10 F) may enhance performance in some applications. An output capacitor (4.7 F to 10 F) may be used to reduce ripple.
Derating Curve
100 80
60
40
Mechanical Dimensions
Side
20
0 -40 -20 0 5 15 25 35 45 55 65 75 85 95 105
0.12 (3.05) 0.10 (2.54)
Ambient Temperature 1C
Pin Connections
Pin 1 Single -Vin NC No Pin +Vout -Vout +Vin Dual -Vin NC Common +Vout -Vout +Vin
0.10 (2.54)
0.60 (15.24)
0.80 (20.32)
Capacitive Load
Single Output Dual Output F Max F Max 470 !390
7 8
7
1
Bottom
14 11 9 8
0.40 (10.2)
9 11 14
0.01 (0.25)
0.01 (0.25)
0.05 (1.25)
NC = No Connection Notes: All dimensions are typical in inches (mm)
Tolerance x.xx = !0.01 (!0.25) Pin 1 is marked by a "dot" or indentation on the top of the unit
Note: "T" = 0.27 (6.85) For 5, 12 & 24 VDC Input Models 0.30 (7.50) For 48 VDC Input Models
MicroPower Direct
232 Tosca Drive, Stoughton, MA 02072 www.micropowerdirect.com sales@micropowerdirect.com phone: (781) 344 - 8226 * fax: (781) 344 - 8481

▲Up To Search▲

Price & Availability of G223

	To Download G223 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .